Home  
Site Partners: SpotterGuides Veloce Books  
Related Sites: Your Link Here  

Go Back   TenTenths Motorsport Forum > Racing Talk > Racing Technology

Reply
 
Thread Tools Display Modes
Old 12 May 2008, 18:40 (Ref:2200360)   #1
Alex Hodgkinson
Veteran
 
Alex Hodgkinson's Avatar
 
Join Date: Aug 2004
England
Derby
Posts: 1,010
Alex Hodgkinson should be qualifying in the top 10 on the grid
Pedal boxes

Hello all,

We're currently building a Mazda RX-7 to race in the GT Cup and/or Britcar.

These cars are very small, so getting things to fit in the cockpit (let alone the driver) is a struggle. Having spent two days fitting the seat and electric power steering system correctly we're now looking at pedal boxes.
As the driver I have a total dislike of pedals which hang down, so we've been looking at floor mounted pedal boxes, all the time looking for a really short box (<150mm/6in)

I found these on the ap site which looked just the job;

http://apracing.com/info/products.as...edal_2351_2342

Phoned up AP today and the chap on the other end told me to "make sure I was sitting down" - they're £3000!!

So, basically I'm looking for a pedal box which is floor mounted, very short and under £1000. I've seen these - http://www.tiltonracing.com/content....st2&id=399&m=b - but I'm not sure how much they'll be. Probably somewhere around the £1500 mark, I'm expecting.

I know a few of you have done this sort of project yourselfs, so what can you all suggest?
Alex Hodgkinson is offline  
__________________
Keep living the dream!
Quote
Old 12 May 2008, 18:52 (Ref:2200376)   #2
vjay48
Racer
 
Join Date: Aug 2007
Posts: 163
vjay48 should be qualifying in the top 10 on the grid
if your could cure you dislike of pedals that hang down a mk 2 escort pedal box for a couple hundred quid,will fit a lot of cars with a bit of tweaking,i think because its simple you can adapt it? have a look on rally design.
vjay48 is offline  
Quote
Old 12 May 2008, 18:59 (Ref:2200387)   #3
vjay48
Racer
 
Join Date: Aug 2007
Posts: 163
vjay48 should be qualifying in the top 10 on the grid
just had a look on rally design,do a floor mounting pedal box,looks good value,we bought box from them,good price,works well
vjay48 is offline  
Quote
Old 12 May 2008, 19:00 (Ref:2200388)   #4
zac510
Veteran
 
zac510's Avatar
 
Join Date: Nov 2005
Posts: 2,714
zac510 should be qualifying in the top 10 on the grid
They are a third that price on that 'demon' website as an example.. But without the cylinders. Tiltons are cheaper.
zac510 is offline  
Quote
Old 12 May 2008, 19:50 (Ref:2200421)   #5
Alex Hodgkinson
Veteran
 
Alex Hodgkinson's Avatar
 
Join Date: Aug 2004
England
Derby
Posts: 1,010
Alex Hodgkinson should be qualifying in the top 10 on the grid
Demon Thieves? I always avoid buying from that lot. Actually I notice that they don't advertise the AP product I was looking at. They'd probably be asking £4000 for it if they did.

I have had a look at those on rally design before, Wilwood I believe? I'm not sure if they're right for us or not. They could be too deep. The important mesurement for me is that from the closest part of the pedal box to the engine bulkhead to the pedal pivot points. The problem is that I'm nearly 6ft tall and Japanese people are not!

Can you find any dimensions for the Wilwood pedal boxes? I've had a quick look but can't find any.
Alex Hodgkinson is offline  
__________________
Keep living the dream!
Quote
Old 12 May 2008, 20:00 (Ref:2200434)   #6
zac510
Veteran
 
zac510's Avatar
 
Join Date: Nov 2005
Posts: 2,714
zac510 should be qualifying in the top 10 on the grid
http://www.wilwood.com/Products/005-...fmbp/index.asp
155.7mm it appears.
zac510 is offline  
Quote
Old 12 May 2008, 22:43 (Ref:2200564)   #7
Alex Hodgkinson
Veteran
 
Alex Hodgkinson's Avatar
 
Join Date: Aug 2004
England
Derby
Posts: 1,010
Alex Hodgkinson should be qualifying in the top 10 on the grid
Thanks. Although I actually meant with the master cylinder present. Anyway I think that's illustrated my packaging problems, I need a pedal box to be around 155mm in length with master cylinders present. Doesn't matter about reservoir pots as they'll be mounted seperately.

I'm going to give Tilton a bell about the 900-Series tomorrow. I was just hoping there was a cheaper example out there which somebody could tell me about.
Alex Hodgkinson is offline  
__________________
Keep living the dream!
Quote
Old 13 May 2008, 07:56 (Ref:2200788)   #8
zac510
Veteran
 
zac510's Avatar
 
Join Date: Nov 2005
Posts: 2,714
zac510 should be qualifying in the top 10 on the grid
Yeah that rules the Wilwood out.
Have you followed the progress of the Rx7 already in Britcar? What class are you building it for? (I've no experience, just curious!)
zac510 is offline  
Quote
Old 13 May 2008, 08:38 (Ref:2200824)   #9
tristancliffe
Veteran
 
tristancliffe's Avatar
 
Join Date: Dec 2005
United Kingdom
Norwich, UK
Posts: 1,164
tristancliffe should be qualifying in the top 10 on the gridtristancliffe should be qualifying in the top 10 on the grid
Can you design and make your own? Pedals aren't complicated really, and you can add all sorts of nice things like the spherical bearing mounted m'cyls that have become popular at the higher price regions.
tristancliffe is offline  
__________________
Dallara F307 Toyota, MSV F3 Cup - Class and Team Champion 2012
Monoposto Champion 2008, 2010 & 2011.
Quote
Old 13 May 2008, 19:41 (Ref:2201486)   #10
Alex Hodgkinson
Veteran
 
Alex Hodgkinson's Avatar
 
Join Date: Aug 2004
England
Derby
Posts: 1,010
Alex Hodgkinson should be qualifying in the top 10 on the grid
We're hoping that we should be able to get it on GT3 pace, so most likely class 2. Just as a reference the RX7 currently in Britcar runs in class 4, against Honda Civics and suchlike, but they have the potential to do so much more than that. With 50/50 weight distribution, low Cd (0.29) 950kg, 385bhp and a proper aero package I'm sure you can see where I'm coming from.

It does look like we're going to be building our own pedal arrangement, yes. I had hoped that we'd be able to find something which we could buy and adapt for our own needs, but it seems not. In which case all I need are some example master cylinders and we can crack on.
Alex Hodgkinson is offline  
__________________
Keep living the dream!
Quote
Old 13 May 2008, 23:06 (Ref:2201643)   #11
MikeHart
Rookie
 
Join Date: Jun 2007
United Kingdom
Birmingham
Posts: 38
MikeHart should be qualifying in the top 10 on the grid
Have you maybe thought about fabricating one yourself? You can get some pretty accurate stuff made with laser cutting these days, and the pedal box in our 2008 Formula Student car is pretty compact with vertically mounted master cylinders.

You can just about see it here:

MikeHart is offline  
__________________
"everything should be made as simple as possible, but not simpler" - Einstein
Quote
Old 14 May 2008, 04:26 (Ref:2201750)   #12
Tony C
Racer
 
Join Date: Aug 2003
Australia
Gold Coast
Posts: 295
Tony C should be qualifying in the top 10 on the grid
How about the wilwood reverse swing unit and turn it upside down
Tony C is offline  
Quote
Old 14 May 2008, 11:59 (Ref:2202064)   #13
MechaniX_034
Rookie
 
Join Date: Mar 2008
Posts: 21
MechaniX_034 should be qualifying in the top 10 on the grid
Quote:
Originally Posted by MikeHart
Have you maybe thought about fabricating one yourself? You can get some pretty accurate stuff made with laser cutting these days, and the pedal box in our 2008 Formula Student car is pretty compact with vertically mounted master cylinders.

You can just about see it here:

Just out of curiousity, what would be involved in fabricating one(tolerances-wise) I must apologise up front for my ignorance, but I've never tried putting a pedal box together before and it sounds like a nice project to keep myself occupied for the next few months.
MechaniX_034 is offline  
Quote
Old 14 May 2008, 12:45 (Ref:2202109)   #14
dgh.mr2
Rookie
 
Join Date: May 2008
Posts: 1
dgh.mr2 should be qualifying in the top 10 on the grid
Though not fitted yet I have just bought a complete system from OBP (Optimum Braking Products) for a Toyota MR2. For £395 including VAT and postage!

This consists of three floor mounted pedals - inward (in cockpit) fluid reservoirs, master cylinders and balance brake bar etc. and aloy cover/false floor - description from their site as below:

"All 3 pedal in one unit Hydraulic clutch cockpit fit system (kit includes 3 x M/Cyl, 3 x Res, 1 x Bias Bar, 1 x Res Bracket, 1 x Bias Cable Adjuster) with OBP0208 Top Cover."

The guy I dealt wth - Grant - was very helpful and has offered any help and to make changes should it not fit me comfortably or I need leverages and resistance etc. altered (they have several clinder designs with different pistons/ capacities so can adjust to suit the car/driver.
dgh.mr2 is offline  
Quote
Old 14 May 2008, 15:01 (Ref:2202229)   #15
MikeHart
Rookie
 
Join Date: Jun 2007
United Kingdom
Birmingham
Posts: 38
MikeHart should be qualifying in the top 10 on the grid
Quote:
Originally Posted by MechaniX_034
Just out of curiousity, what would be involved in fabricating one(tolerances-wise) I must apologise up front for my ignorance, but I've never tried putting a pedal box together before and it sounds like a nice project to keep myself occupied for the next few months.
Well, if you want to get it laser cut, you fundamentally just need to get to grips with a CAD package. If you've not used one before, you might struggle a bit, but there are plenty out there to have a 'go' with If you'd rather just stick to the old elbow grease method, then just get hold of some 2mm or thereabouts, sheet steel and start bending and cutting stuff to appropriate sizes and shapes. One good way to start though is to just use some modelling card to mock the whole thing up first.

There are three main things you need to be aware of when designing the thing though, one being that the mounting for the master cylinders needs to be rock solid to prevent any flex and hence poor pedal feel. This can be achieved either by using thicker sheet or by making sure you strengthen the structure around that area. Numbers two and three relate to the virtical location of the master cylinders. You need to have a play around either on CAD or with bits of wood to check you get your ratio of travel right in the cam that converts the forward and backwards motion of the pedal to up and down for the master cylinders. The other is that you need remote brake and clutch reservoirs and to bleed them you'll need to turn the pedal box through 90deg which can be done fairly easily if you design in a removable mounting.

Personally, for the sake of the space in an RX-7 which must be miles more than in our FSAE car I'd go for normal horizontally mounted master cylinders. You could still come up with a far more compact solution for a lot less money though. If you really want to go for minimal space, our virtically mounted pedal box is less than 200mm from the pedal face to the back of the box structure.

For the laser cutting route, use a CAD package and then you can simply send the unfolded drawings of the sheet parts to a company like Midtherm. It's pretty inexpensive and the quality you get is as good as a mass produced pressing. The tolerances are also a lot better too....a 40mm hole will be bang on 40mm.

Once you're all welded up the final thing should be a matter of mm within the design. It certainly wouldn't be enough to worry about. I'll try and get some better pictures of the thing later.

Hope that helps. Let me know if you need any more info.
MikeHart is offline  
__________________
"everything should be made as simple as possible, but not simpler" - Einstein
Quote
Old 14 May 2008, 23:56 (Ref:2202627)   #16
Notso Swift
Veteran
 
Notso Swift's Avatar
 
Join Date: Apr 2006
United Nations
37deg 46'52.36" S 144deg 59' 01.83"E
Posts: 1,908
Notso Swift should be qualifying in the top 10 on the grid
Quote:
Originally Posted by Alex Hodgkinson
As the driver I have a total dislike of pedals which hang down, so we've been looking at floor mounted pedal boxes,
Stop being a prima donna! You just want it because that is what real race cars do.

In all seriousness, I have driven one of these things (I presume this is a S6-8) and they are very tight, the main cage hoop makes it almost impossibly so, you may have to lump it or custom build
Notso Swift is offline  
__________________
Contrary to popular opinion, I do have mechanical sympathy, I always feel sorry for the cars I drive.
Quote
Old 16 May 2008, 14:05 (Ref:2204041)   #17
Alex Hodgkinson
Veteran
 
Alex Hodgkinson's Avatar
 
Join Date: Aug 2004
England
Derby
Posts: 1,010
Alex Hodgkinson should be qualifying in the top 10 on the grid
Meh - maybe :P

What's an S6-8 though? This car I'm working on is a FD3S Mazda RX7, like this:



We will be making the pedal box, yes. It's just something which would've been nice to receive all manufactured and ready to go. We'll be using the pull-type master cylinders (still £240 each!!) and making the pedals, pivot points/mounts etc from top quality aluminium.
Alex Hodgkinson is offline  
__________________
Keep living the dream!
Quote
Old 20 May 2008, 23:58 (Ref:2207883)   #18
MikeHart
Rookie
 
Join Date: Jun 2007
United Kingdom
Birmingham
Posts: 38
MikeHart should be qualifying in the top 10 on the grid
I managed to get some photos of the pedal box I was on about. It's not finished yet clearly, but you get the idea....



MikeHart is offline  
__________________
"everything should be made as simple as possible, but not simpler" - Einstein
Quote
Old 21 May 2008, 00:25 (Ref:2207892)   #19
Notso Swift
Veteran
 
Notso Swift's Avatar
 
Join Date: Apr 2006
United Nations
37deg 46'52.36" S 144deg 59' 01.83"E
Posts: 1,908
Notso Swift should be qualifying in the top 10 on the grid
Yes, that is the Series 6-8, also called 3rd Generation RX7, FD is Chassis

S1-3 were the Classic/orginal type
S4-5 were the 944 style
Notso Swift is offline  
__________________
Contrary to popular opinion, I do have mechanical sympathy, I always feel sorry for the cars I drive.
Quote
Old 25 May 2008, 07:18 (Ref:2211013)   #20
JamesH
Veteran
 
JamesH's Avatar
 
Join Date: Aug 2006
United Kingdom
Christchurch, Cambs, UK
Posts: 2,126
JamesH has a real shot at the championship!JamesH has a real shot at the championship!JamesH has a real shot at the championship!JamesH has a real shot at the championship!JamesH has a real shot at the championship!JamesH has a real shot at the championship!
Try a kit car manufacturer - eg Locost. I have a smallish pedal box with cylinders and remote reservoirs which cost about 150 or so I think. Or check out the source of all race car parts, ebay - lots of stuff there.

e.g.

http://cgi.ebay.co.uk/AUTOGRASS-PEDA...ayphotohosting

You can get ideas from there even if you dont want the item!!

James
JamesH is offline  
__________________
Locost #54 Boldly Leaping where no car has gone before. And then being T-boned. Damn.
Survivor of the 2008 2CV 24h!! 2 engines, one accident, 76mph and rain.
Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New Boxes for the Post Chiefs!!! archaic gold Marshals Forum 13 30 Apr 2008 12:27
pedal mounts gttouring Racing Technology 7 15 Dec 2007 00:28
A1 GP Tool Boxes AstroBoy A1GP 4 20 Jul 2006 13:16
pvl retarder boxes pmb5 Kart Racing 4 25 Aug 2004 19:21
3 Pedal Prost? joseff Racing Technology 14 31 Aug 2001 23:14


All times are GMT. The time now is 14:56.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Original Website Copyright © 1998-2003 Craig Antil. All Rights Reserved.
Ten-Tenths Motorsport Forums Copyright © 2004-2021 Royalridge Computing. All Rights Reserved.
Ten-Tenths Motorsport Forums Copyright © 2021-2022 Grant MacDonald. All Rights Reserved.