|
|||||||||||
|
|||||||||||
7 Nov 2015, 19:36 (Ref:3588838) | #1 | ||
Racer
Join Date: Jun 2005
Posts: 168
|
FJ - chain drive drop-box?
this is a technical type post so may be in the wrong place but has historical content.
so in our obscure, one off, over weight, under powered, French Canadian, front engined Formula Junior we have a chain drive drop box bolted to the front of the diff housing to lower the height of the prop shaft and therefore lower the seat. Anyway this thing screams away - a quick clip of how noisy at L-J Sjoberg last FJ invite https://www.youtube.com/watch?v=86PRfud0o_g also the drop-box is way way to hot to touch by the end of a race. anyone got any experience with chain drive drop-boxes? the box has a sprocket on the nose of the diff so uses the diff pinion bearings at the top and has a sprocket on a shaft running on sealed bearings at the bottom - yep I know it is upside down! so the oil which is ep90 is only lubricating the chain and this is like stirring treacle, so the question is would I be better with an ATF or similar? |
||
|
7 Nov 2015, 20:24 (Ref:3588854) | #2 | ||
Veteran
Join Date: Dec 2001
Posts: 6,358
|
I have no experience with boxes like that, but I have some experience of industrial power transmission products.
I assume the box is filled, or partially filled, with EP90? If so, part of your problem could be oil churning. EP90 is not, in my opinion, a suitable lubricant for chains - you need a specialised chain lubricant. I'd be looking at a grease which can be applied direct to the chain & which has anti-fling properties to ensure that it stays where it's needed; that could well be nothing more than a motorcycle chain spray! If you want something more high-tech, look at the products of specialist lubricant manufacturers. I've had very good results from a Kluber grease in a troublesome gearbox application, Rocol also has a wide range of lubricants for many different applications. |
||
__________________
Doing an important job doesn't make you an important person. |
8 Nov 2015, 13:40 (Ref:3589025) | #3 | |
Racer
Join Date: Mar 2007
Posts: 100
|
I would doubt you need any oil in the box at all. You need to check the spec of the chain. It may well be "o ring" chain with seals to keep the EP90 out of the bearing area!
The chain is going far faster than it is designed to, but the chain load is, I bet, far lower than the designed maximum Can you adjust the tension. check it isnt too tight. But basically you have there a mechanical oil heater. Half fill that with oil and I bet it is consuming 4bhp at 6000 rpm |
|
|
9 Nov 2015, 09:32 (Ref:3589210) | #4 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
The whole thing may work better with a smaller pitch and a duplex or triplex chain.
A Lambretta runs a long chain drive with a light tensioner on the slack side ( usually uprated with a PTFE block these days) There is but a puddle of ST90 to keep the clutch plates and gearbox wet. the chain is 1/2" pitch ( as a Ford FJ cam drive) and duplex, the same is available as a triplex also, that may help. |
|
|
9 Nov 2015, 13:37 (Ref:3589251) | #5 | |
Racer
Join Date: Nov 2005
Posts: 122
|
I am not 100 % sure, but I think Ingvar Malm has a chain drop-box in his Elva 100, or at least that he has tried it. I will check with him.
|
|
|
9 Nov 2015, 15:10 (Ref:3589267) | #6 | |||
Veteran
Join Date: Dec 2001
Posts: 6,358
|
Quote:
An O-ring chain would not, in any case, be of much benefit in this application. They are intended for use in harsh environments, where the chain is exposed to contaminants such as dirt & water; their main use is for motorcycle drive chains. They do also incur a small power loss - one of the claims for DI's X-ring chains is that the power loss is less than for a comparable O-ring chain. |
|||
__________________
Doing an important job doesn't make you an important person. |
9 Nov 2015, 22:47 (Ref:3589362) | #7 | ||
Veteran
Join Date: Nov 2006
Posts: 9,426
|
Personally I would use a much thinner oil, all timing chains on engines last for years and most run on 5w30 oils now. I would also use some ZX1 mixed with it and only half fill it.
|
||
__________________
Balls of steel (knob of butter) They're Asking For Larkins. ( Proper beer) not you're Eurofizz crap. Hace más calor en España. Me han conocido a hablar un montón cojones! Send any cheques and cash to PO box 1 Lagos Nigeria Africa ! |
10 Nov 2015, 01:56 (Ref:3589392) | #8 | |
Veteran
Join Date: Jun 2009
Posts: 8,088
|
I don't know whether your rules allow it, but you may be able to substitute your chain drive for a silent type chain drive, they are smoother, quieter, more efficient and can run at higher speed than your sprockets.
Have a look here http://www.ramseychain.com/prod_sc.asp and speak to them. |
|
|
10 Nov 2015, 09:45 (Ref:3589446) | #9 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
you could probably run a belt drive dry.
These have been around for a few years now, can run dry or in oil http://bristollambretta.webs.com/BELT%20DRIVE.jpg its only a small belt, but even the well tuned motors are only putting out 35 ish HP Modern Hardley rideables for Midlife crisis consultants run belt drives. |
|
|
10 Nov 2015, 10:09 (Ref:3589453) | #10 | |
Racer
Join Date: Nov 2005
Posts: 122
|
Ingvar Malm confirmed that he has experience of both a gear drop-box and a chain drop-box in his Elva 100. He says that the box with the chain does not run any hotter than the one with gears. Rather the opposite. He is using a normal hypoid oil in both types of box, i.e. something around SAE90. One thing he has done, though, is to make sure that there is a good flow of air around the drop-box. He has a scoop to get air in and has hole to let it escape. Before he did this, it was running too hot (both the gear type and the chain type).
|
|
|
10 Nov 2015, 12:39 (Ref:3589477) | #11 | |
Veteran
Join Date: Apr 2002
Posts: 9,710
|
So it needs wind to cool it.
Where is the seat exactly? |
|
|
11 Nov 2015, 09:19 (Ref:3589685) | #12 | |
Racer
Join Date: Nov 2005
Posts: 122
|
Ingvar Malm just called with some additional info which he forgot to mention yesterday. Most important: the casing for the chain is connected to an oil tank of about 1 litre in volume. The tank is installed at a height which results in the chain casing being filled to about one third. The tank is ventilated to the atmosphere to prevent over pressure.
|
|
|
10 Dec 2015, 10:52 (Ref:3596809) | #13 | |
Veteran
Join Date: Jun 2009
Posts: 8,088
|
||
|
15 Dec 2015, 19:56 (Ref:3597995) | #14 | ||
Racer
Join Date: Jun 2005
Posts: 168
|
having pulled it all to bits, and found that the top sprocket was welded to an original diff flange that had been spun down on a lathe so we had a seal between the drop box and the diff, this gave us the ability to use different oil.
the chain is a modern o seal type chain and the bearings on the drop box input shaft were sealed bearings. in theory there should be no need for any oil and the box could be run dry. but there are some witness marks where the chain has come into contact with the drop box casing and whilst this shouldn't be a problem obviously this will cause friction with the resultant heat. having re-assembled the diff with the new crown wheel and pinion (a more sensible ratio we hope) we put the drop box back together and have added a small amount of AFT as a splash lubricant. so in the first test down the road, the only problem is the ATF not wanting to stay in the drop box - it was running down the splines on the input shaft and coming out between the flange face and the prop shaft! a bit of sealer and try again sorted. not much more to say, the little motor is in a big tin box heading towards a test session/free practice/ for the end of Jan at Zwartkops. Richard |
||
|
16 Dec 2015, 02:18 (Ref:3598068) | #15 | |
Veteran
Join Date: Jun 2009
Posts: 8,088
|
Thanks Richard good to know.
Good Luck at Zwartkops in Jan, it is a great little circuit. |
|
|
16 Dec 2015, 08:54 (Ref:3598109) | #16 | ||
Veteran
Join Date: Dec 2001
Posts: 6,358
|
|||
__________________
Doing an important job doesn't make you an important person. |
16 Dec 2015, 17:07 (Ref:3598178) | #17 | ||
Racer
Join Date: Jun 2005
Posts: 168
|
|||
|
29 Mar 2016, 19:21 (Ref:3628504) | #18 | ||
Racer
Join Date: Jun 2005
Posts: 168
|
update on the chain drive drop box
well it broke not actually sure if the chain broke jamming the sprocket on the diff which caused the drive shaft to snap and the resultant suspension failure or the drive shaft broke up causing suspension failure, jamming on the rear upright and snapping the chain anyway if you want a laugh this is what it looked like: https://www.youtube.com/watch?v=EUbqT1tZqXY Richard |
||
|
30 Apr 2016, 09:23 (Ref:3637293) | #19 | ||
Subscriber
Veteran
Join Date: Oct 2007
Posts: 8,740
|
Yesterday was first time I had driven a car with a drop box . Tell me are they always that noisy
|
||
|
30 Apr 2016, 20:55 (Ref:3637405) | #20 | ||
Racer
Join Date: Jun 2005
Posts: 168
|
well the one in the Autosport howls, but that the only one I have experience of - it is than noisy I have to wear ear plugs.
Richard Last edited by rbm; 30 Apr 2016 at 20:58. Reason: typo |
||
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
BBC may drop F1 in economy drive? | Paradise City | Formula One | 102 | 16 Mar 2011 01:15 |
Obscure FJ | graham allen | Motorsport History | 23 | 11 Nov 2005 08:31 |
turbo hayabusa chain drive? | DanJR1 | Racing Technology | 8 | 21 Jan 2004 12:26 |
Saab Fj | WANHER | Motorsport History | 2 | 14 Oct 2001 10:00 |